P5 Indoor 32 x 64 RGB LED Display Module

Product Description

Module:P5 Full Color LED Module
Pixel pitch 5 mm
Module Size 320X160 mm
Model Pixel 64X32 Pixels
lattice density 40000 dots/square meter
Pixel form 1R1PG1GB SMD2121
Best viewing distance 5m~40 m
Max power consumption 800W/square meter
Ave power consumption 500W/square meter
Drive mode( Optional) Constant current 1/16 scan
Control system DVI card+Full color control card
Pixel type Real pixel
refresh frequency >=400HZ
Horizontal View Angel > 110 degree
Working Environment Temp:-20Celsius degree-+60Celsius degree
Humidity : 10%-90%
Working voltage 5V / DC
Lifetime >=100000 hours
Gray scale 12 bit/ 1 color
Color display manual adjust
Brightness 1600 cd/square meter
Blind spot rate <0.00001

Micro SD Card Adapter

Overview

– This MicroSD Card Adapter module is a Micro SD card reader module with an SPI interface via the file system
driver, requiring an Arduino (or comparable) microcontroller system to complete the MicroSD system to read and
write files

– Arduino users can directly use the Arduino IDE that comes with an SD card to complete the library card
initialization and read-write.

Features
– Supports Micro SD and Micro SDHC cards (high speed card)
– The level conversion circuit board can interface with 5V or 3.3V levels
– The power supply input (Vcc) is 4.5V to 5.5V
– The module includes an AMS1117-3.3 3.3V voltage regulator circuit to support the 3.3V
– The communication interface is a standard SPI interface
– 4x M2 screw positioning holes (2.2mm diameter) for easy installation

Interface Description
– Control Interface: Six pin header (GND, VCC, MISO, MOSI, SCK, CS)
– GND: Ground
– VCC: DC power supply input – 4.5V to 5.5V
– MISO, MOSI, SCK: SPI bus
– CS: Chip select signal pin

3.3V regulator circuit
– AMS1117-3.3 LDO regulator output 3.3V for level conversion chip, Micro SD card supply

Level conversion circuit
– Micro SD card to signal the direction of converts 3.3V
– MicroSD card interface to control the direction of the MISO signal is also converted to 3.3V
– General AVR microcontroller systems can read the signal

Quadruple Bus Buffer Gate
-The LVC125A device is a quadruple bus buffer gate featuring independent line drivers with 3-state outputs.

 

 

 

 

 

Arduino Uno

Overview
– The UNO R3 is the best board to get started with electronics and coding. If this is your first experience with electronics and coding, the UNO is the most robust board you can start playing with. The UNO R3 is the most used and documented board of the whole Arduino family. The UNO R3 is a microcontroller board based on the ATmega328P. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz quartz crystal, a USB connection, a power jack, an ICSP header and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.

Differences with other boards
– The UNO R3 differs from all preceding boards in that it does not use the FTDI USB-to-serial driver chip. Instead, it features the Atmega16U2 (Atmega8U2 up to version R2) programmed as a USB-to-serial converter.

Revisions
– 1.0 pinout: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible with both the board that uses the AVR, which operates with 5V and with the Arduino Due that operates with 3.3V. The second one is a not connected pin, that is reserved for future purposes.
– Stronger RESET circuit.
– Atmega 16U2 replace the 8U2. Means a higher transfer rate and memory.

Communication
– The Uno has a number of facilities for communicating with a computer, another Uno board, or other microcontrollers. The ATmega328 provides UART TTL (5V) serial communication, which is available on digital pins 0 (RX) and 1 (TX). An ATmega16U2 on the board channels this serial communication over USB and appears as a virtual com port to software on the computer. The 16U2 firmware uses the standard USB COM drivers, and no external driver is needed. However, on Windows, a .inf file is required. The Arduino Software (IDE) includes a serial monitor which allows simple textual data to be sent to and from the board. The RX and TX LEDs on the board will flash when data is being transmitted via the USB-to-serial chip and USB connection to the computer (but not for serial communication on pins 0 and 1).

Memory
– The ATmega328 has 32 KB (with 0.5 KB occupied by the bootloader). It also has 2 KB of SRAM and 1 KB of EEPROM.

 

 

 

 

 

P10 Single Color 16 x 32 Red Dot Matrix Display

10mm pixel semi-outdoor indoor red 320*160 32*16 one color hub12 monochrome p10 led sign module,p10 single color red panel

 

Requires – Either XC2 Single Color LED Control Card or XU2 Single/Dual Color LED Control Card.

Best view distance:9M – 30M

Display color:Red

Brightness: 2000Nits/square meter

Hub type: 12

Display type: Character

Size: 320*160mm

Resolution:32*16

Scan:1/4

Weight:420g

Working Voltage: DC 5V

Use for: Semi-outdoor